Mountonus Brodit ProClip Mount Shop Logo
UK Trusted Supplier of Brodit ProClip Mount and Car Cradle Holder Solutions.

Toughshield R500+
Brodit Active Car Cradle Holder For Fixed Installation (Brodit 513588)

Active Holder For Fixed Installation for Toughshield R500+
Reference ID: 51294.
Product Type: Brodit Active Car Cradle Holder For Fixed Installation.
Part Number: Brodit 513588.
Fitment: Toughshield R500+ For All Countries.

Price:

£ 72.13
Click the button below to add this product to your Shopping Cart.
You will be automatically redirected to your Shopping Cart page after that.
Add to Shopping Cart

Product Description:

An active holder which is to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior!

You can choose to use the holder as an active holder for charging of your device only, or to connect an adapter to the Molex connector for additional features. Then you can use the holder also for power supply of a GPS receiver or other own solutions (can not be used for data communication or audio connection).

12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended. The holder is attached onto a tilt swivel so you can easily adjust your device in order to avoid light reflection. Attach onto a ProClip Mounting Platform.

This Product is also Compatible with the Following Device :

The drop-down list below provides a list of other devices which this Active Car Cradle Holder For Fixed Installation also compatible with. That means you can mount the listed devices using this product "as is" without any modifications or additional preparation.

Select a device from the drop-down list below and click the button to the right to see the detail page for that particular application.

How to Install Active Car Cradle Holder For Fixed Installation for Toughshield R500+:

Please read all of the instructions and look at the pictures before attaching the holder. Important Note: Route the cable from the holder into the vehicle dashboard and route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle.

1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back.

2. Place the attaching plate onto the desired position. Screw the attaching plate into place with the enclosed screws.

3. Place the holder over the attaching plate so the screw fits in the hole in the tilt swivel. Tighten the screw until the holder is firmly in place, but still can be adjusted.

4. The holder is in place.

Installation Photos:

Installation Photo Installation Photo
Installation Photo Installation Photo

Other Products for Toughshield R500+:

Part No: Brodit 512588
Product Type: Brodit Active Car Cradle Holder With Cig-Plug
Product Fits: Toughshield R500+ for all countries
Placement:
Price: £ 46.92
Description:
With tilt swivel. Fits devices with standard and extended battery. With fly lead.
Technical Information:
The active holder charges your battery when it is in the holder. The charging device connects to the PDA automatically when you put the PDA in the holder. The holder is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. Connects to the vehicle's cigarette lighter socket, 12/24 Volt. Attach onto a ProClip Mounting Platform.
More Info
Part No: Brodit 941011
Product Type: Brodit Charging Cable
Product Fits: Toughshield R500+ for all countries
Placement:
Price: £ 18.72
Description:
Charging cable Plugs directly into your Cigarette lighter. With Micro-USB connector, 2A charging. With USB A outlet in the cig-plug, 1A charging. 12/24V.
Technical Information:
Charging cable with cig-plug. With Micro-USB connector, 2A charging. You can charge a second device via the USB A outlet in the cig-plug, 1A charging. Can be used with Brodit passive holders. 12/24V. Length (+cig-plug 77 mm): 46 cm, stretched: 130 cm (or a bit more if necessary).
 
The Micro-USB connector house is angled. This means that the cable goes either on the back or on the front side, depending on the device. In order to make sure you get the cable on the side you want, please look at the picture and compare with your device. If you prefer the connector pin to be the other way around, please see item no 941010.
 
Charging specifications:
Input voltage: DC/10-30V
Charging voltage: DC/4.75-5.25V
Output current(Typ): 2.0A
LED charging indicator: Power on.
Operating temperature: 0°C ~ +40°C
Storage temperature: -20°C ~ +60°C
Approvals: E, CE, FCC, ROHS

More Info
Part No: Brodit 944011
Product Type: Brodit Charging Cable
Product Fits: Toughshield R500+ for all countries
Placement:
Price: £ 15.54
Description:
Micro USB. 12/24V. Angled.
Technical Information:
For use in the vehicle’s cigarette lighter socket, charges your unit. Can be connected to the unit when it is in a passive holder.
More Info
Part No: Brodit 511588
Product Type: Brodit Passive Car Cradle Holder With Tilt Swivel
Product Fits: Toughshield R500+ for all countries
Placement:
Price: £ 24.89
Description:
Fits devices with standard and extended battery.
Technical Information:
With your PDA in a passive holder attached onto the dashboard it is always within easy reach -safe and convenient. The holder is mounted onto a tilt swivel so it is adjustable for avoiding light reflection on the screen. It is easy to put the PDA in the holder, and to take it out of the holder. You can connect e.g. a charging cable to the PDA when it is in the holder.
More Info
Additional Information

Additional Information:
Tablet PC Holder.

Use a Tablet PC holder for your own convenience and safety!

You can attach a charging cable when the device is in the holder.

You can easily take the monitor with you when leaving the vehicle.

The holder comes with a tilt swivel, so it is adjustable for avoiding light reflection in the screen.